Vmax 4 parts, 1992 & 1996

M

mtbombsqd

New member
96 chassis & 159" tunnel extensions with aluminum rack
96 Rear & side heat exchangers
96 Steering post & components
96 gas tank
96 fuel pump/oil injectors
96 hood, pod - right side crack fair condition
96 hoses
96 Handle bar, throttle & brake controls, hand warmers

92 hood black

92 - 2 stock heads used.
92 coils
92 air boxes 2 each, stock
92 drive shaft 9 tooth drivers
92 secondary

Red windshield bag


Updated list as of 1/18/06 thanks for all the interest, sorry if you asked about it and its not listed, it was a first come with money first served.
 

Attachments

  • front side view.JPG
    front side view.JPG
    127.5 KB · Views: 186
  • Rear exchanger.JPG
    Rear exchanger.JPG
    77.7 KB · Views: 182
  • 92 hood.JPG
    92 hood.JPG
    97.5 KB · Views: 85
  • 92 hood side.JPG
    92 hood side.JPG
    111.9 KB · Views: 83
  • DCP_2475.JPG
    DCP_2475.JPG
    85.7 KB · Views: 85
Last edited:

Fellas, Thanks for the interest. I'm trying to upload pics, should have them today. The parts are in Utah 84075, UPS ground in 7 days is probably the best, larger parts most likey less than $80. Seat is in very good condition, strut cans are not perfect, small dings in both of them. Windshield is smoked in fair condition not broken at all, just used. I did the best I could; however, This sled was way to much fun not to ride, so the parts are going to be used. YYMAX $300 for the AAEN's & shipping.
 
Last edited:
How much for the seat, along with, would it fit a 92? And the reeds, are they the Vforce3 carbon fiber ones? I'm interested in both of those. :)
Thanks, Lewis
P.S. You can also email me at lkoberg15@gmail.com
 
Seems to be alot of interest in the seat, the first $100 plus shipping cost will get the seat. I can't tell you for sure if it will fit the 92. I've had both sleds but never swapped seats. If memory serves they both mound the same way but the 96 tunnel is wider than the 92. I have a set of VForce reeds that are carbon fiber, but not VForce3 reeds.
 
:banghead: how much for the carbs and how much of a difference is there would also be interested in the motor but i guess its not available:banghead:
 
PSI carbs are pretty amazing, every adjustment can be made without removing anything. How much they will help would be determined by what your running Sid. Stock 750 or 800 you would probably be hurting performance. There is a Hauck 880 kit for sale on this site for 1200, which is a good deal, these carbs will put some life in that motor. Check the psiperformance.com site out you can read all about them. I'm in no big hurry to sell them, at over 500 each new they would be hard to replace. I've never seen them for sale used either.
 
Kevin b give me an offer over shipping and it yours.

Busted max I have a 96 secondary with a highmark roller cover 42.5 degree helix, black spring, jackshaft is gone, chain case is a 89A not a 8DU, I think they are close if not the same, drive shaft had less than a dozen rides on it and is in good condition, the extrovert drivers are bad when pressed on, I'll take an offer plus shipping.
 
Last edited:
Not yet, give ma an offer, medium hight, smoked, used not broken condition. Its not off yet, screw holes could be cracked and I can't see, but face value looks good.
 
You must log in or register to reply here.


Back
Top